Marine, Diving and Offshore

Titanium Tools for Marine, Diving and Offshore Work

Saltwater does not negotiate. Every steel tool near it is on a clock, and the only thing that slows the clock is your own labour. Titanium takes the clock away.

Commercial and Offshore

The cost is not the tool, it is the hour a tech spends at the end of every shift cleaning a kit. Titanium removes that step rather than shortening it.

Dive and In-Water Work

Anything that goes in the water and comes out again is the worst case for steel. Titanium tools can live in a rinse tank.

Boat Owners and Cruisers

Worth it for the few tools you cannot be stuck without, not for a whole set. We will say so rather than sell you the kit. Also see our EOD and bomb disposal tools and fab and cleanroom tools.

What Saltwater Does to a Steel Tool

These are the failures that make a marine tool kit a recurring cost instead of a one-time purchase.
Titanium Non-Magnetic Double Open End Wrench 5mm x 5.5mm MRI-Safe Non-Ferrous Tool

Where Steel Gives Up

Your real alternative is not rusty carbon steel. It is 316 stainless, which is genuinely good and much cheaper. The difference shows up in one place, and it is the place tools actually live.

Pitting under a clamp
316 stainless resists general corrosion well but still pits in warm, stagnant, chloride-rich spots. Under a clamp, inside a socket, in the bottom of a roll that never dried.
The fastener you cannot get to
The wrench in the cockpit locker used twice a season is the one that seizes. It fails on the day you finally need it.
The end-of-shift ritual
Rinse, dry, oil, spray, repeat after the next job. Multiply that by every shift and it is a real line on the labour bill.
Stowed wet
Tools that go away damp corrode from the inside of the roll outward. Nobody notices until something is already scrap.
Shop Titanium Tools Talk to Us About Quantity

Where Titanium Actually Wins

Narrow, specific, and worth stating plainly rather than overselling.
Titanium wrench front view - MRI-Safe Non-Magnetic | FDM Enterprises

The Case, Honestly

If your tools dry out between uses, 316 stainless will serve you and cost far less. If they live wet, go in the water, or sit in a locker that never dries, titanium is the material that ends the problem instead of managing it.

Effectively zero corrosion in seawater
Titanium forms a self-repairing oxide layer, so it is inert in salt water rather than slow to rust. Published rates sit below 0.0005 mm per year, with no pitting or crevice corrosion.
About 44% lighter than steel
Grade 5 titanium is 4.43 g/cm3 against roughly 7.85 for tool steel. On offshore work the kit gets carried and hoisted by hand all day.
It will not deflect a compass
Titanium is non-magnetic and non-ferrous, so it does not register on a magnetometer. That matters on a dive, and it matters more on survey work.
Built for low magnetic signature
Mine countermeasures vessels specify machinery and equipment in non-magnetic material with ferrous minimised. A steel tool kit is ferrous mass in a hull engineered to have none.
Browse Marine Tool Sets Request Quantity Pricing

Where to Start

Start with the tools that get wet most and the ones you cannot afford to have seize.

  • Titanium open end wrench non magnetic non ferrous tool

    Titanium Wrenches

    Titanium Wrenches for MRI Equipment Service The complete FDM Enterprises lineup of titanium wrenches — pipe, adjustable (crescent), combination, open-end, and ratcheting. Every wrench is Grade 5 (6Al-4V) titanium, non-magnetic, non-ferrous, and MRI Zone IV safe. Available in metric and SAE. Titanium Pipe Wrench Titanium Pipe Wrench — 8", 10",...

    Titanium Wrenches
  • MRI-safe titanium ratchets and sockets - non-magnetic 3/8 drive socket tools

    MRI-Safe Titanium Sockets & Ratchets | FDM Enterprises

    Titanium Sockets & Ratchet Tools for MRI Service The complete FDM Enterprises titanium socket and ratchet system in 3/8" drive — Grade 5 (6Al-4V) titanium, non-magnetic, non-ferrous, and MRI Zone IV safe. Titanium Socket Set & Single Sockets 16-Piece Titanium Socket Set — metric, 3/8" drive Single Titanium Socket (Metric)...

    MRI-Safe Titanium Sockets & Ratchets | FDM Enterprises
  • Titanium screwdriver non-magnetic non-ferrous

    Titanium Screwdrivers

    Titanium Screwdrivers — MRI-Safe Non-Magnetic FDM Enterprises titanium screwdrivers are Grade 5 (6Al-4V) titanium — completely non-magnetic, non-ferrous, and MRI Zone IV safe. Steel screwdrivers (even "demagnetized") become projectiles inside an MRI magnet room and trigger fringe-field alarms during PM. Titanium eliminates both problems. Titanium Screwdriver Set 6-Piece Titanium Screwdriver...

    Titanium Screwdrivers
  • Titanium needle nose pliers non magnetic MRI safe tool

    Titanium Pliers & Cutters

    Titanium Pliers for MRI & Non-Magnetic Service Work FDM Enterprises stocks the most complete line of titanium pliers for MRI service — every plier is Grade 5 (6Al-4V) titanium, non-magnetic, non-ferrous, and MRI Zone IV safe. Also used for EOD ordnance handling, marine and diving service, and semiconductor cleanroom work....

    Titanium Pliers & Cutters

What You Give Up

Titanium is not non-sparking. For a flammable atmosphere you need beryllium copper, and we will tell you that rather than sell you the wrong material. It is also less stiff than steel and it costs more.

Care and Storage

Rinse with fresh water if convenient. Do not oil it, and do not spray it with corrosion inhibitor - it does nothing on titanium and makes the handles slippery.

Commercial and Government Buyers

FDM Enterprises is a verified Veteran-Owned Small Business and sells direct to commercial, institutional and government buyers. Contact us for quantity pricing.

Frequently Asked Questions

No. Titanium forms a self-repairing oxide layer that makes it inert in seawater rather than slow to corrode. Published data puts the corrosion rate below 0.0005 mm per year, and titanium recovered after years at depth shows no measurable corrosion, including no pitting under marine growth.

For most conditions 316 stainless is good and much cheaper. Titanium wins in one specific way that matters if your tools stay wet: 316 remains vulnerable to pitting and crevice corrosion in warm, stagnant chloride conditions, and titanium is not. If your tools dry out between uses, stainless is the sensible buy.

About 44% lighter than the same tool in steel. Grade 5 titanium has a density of 4.43 g/cm3 against roughly 7.85 for chrome-vanadium tool steel and 8.0 for 316 stainless. That figure is calculated from material density, not weighed.

No. Titanium is non-magnetic, non-ferrous and corrosion resistant, but it is not non-sparking. For a flammable atmosphere you need beryllium copper. We would rather tell you that than sell you the wrong tool.

Grade 5 titanium, Ti-6Al-4V, has tensile strength comparable to many tool steels. It is less stiff, so it flexes more under the same load, which the tool design compensates for with thicker sections. For normal hand-tool torque there is no practical strength penalty.

No. Titanium is non-magnetic and non-ferrous, so it will not deflect a compass or register on a magnetometer. This matters for dive work near a compass, for hydrographic and geophysical survey vessels, and for mine countermeasures vessels built to a low magnetic signature standard.

Yes. FDM Enterprises is a verified Veteran-Owned Small Business and sells directly to commercial, institutional and government buyers. Contact us for quantity pricing and purchasing documentation.

Grade 5, Ti-6Al-4V. It is the standard structural titanium alloy, the same specification used in aerospace and marine hardware, and it is what gives these tools their strength-to-weight ratio and their seawater performance.